產品細節介紹
FIREYE 45UV5-1000自檢火焰掃描器
使用以太網通信CPU模塊內的Ethernet接口不能在直到配置了有效的IP地址。必要的以太網尋址信息必須在實際之前配置網絡操作,或從意外更改中恢復以太網接口處的以太網尋址數據。使用其中一個以下方法用于初始分配IP地址:? 將串行終端連接到PAC系統RX7i。然后使用CHSOSW命令輸入所需的IP地址。有關詳細信息,請參閱PAC系統
TCP/IP Communications Station Manager手冊,GFK-2225。
? 使用SetIP臨時為模塊分配IP地址以太網上的工具。有關詳細信息,請參閱TCP/IP以太網PAC系統通信,GFK-2224。
? Ethernet接口自動獲得臨時IP
來自網絡上BOOTP服務器的地址。有關詳細信息,請參見PAC系統的TCP/IP以太網通信,GFK-2224。
一旦設置了臨時IP地址,以太網可以通過網絡訪問接口(如機器編輯編程軟件)。然后程序員應該用于為Ethernet接口配置正確的IP地址。
SRTP連接時更改IP地址打開可能會生成日志事件
打開與遠程SRTP建立的SRTP服務器連接當RX7i的IP地址為更改(通常通過將新的硬件配置存儲到RX7i)。
Series 90 SRTP客戶端(“SRTP通道”)報告9690H或0190H狀態;
SRTP連接可能會保持打開狀態,直到由于客戶端超時,連接被終止。不應更改AUP參數不應更改高級用戶參數“wsnd_buf”由用戶決定。更改此參數的值可能會導致LAN LED熄滅,Ethernet接口斷開連接。重載可能會阻塞Station Manager,如PACSystems Station的TCP/IP通信中所述管理器手冊,GFK-2225,重型EGD和/或SRTP負載可以阻止Station Manager操作。
EGD生產的一次延遲(和可能消耗量),如果超過24 SRTP服務器連接同時啟動如果建立了24個以上的SRTP服務器連接同時,EGD生產可能會短暫延遲24號之后的連接通電。如果EGD消耗加速被禁用,則EGD消耗也將延遲。僅發生延遲第一次建立SRTP服務器連接時通電后的時間。第一個24 SRTP沒有延遲服務器連接。
極大量EGD生產/消耗服務器可能導致EGD命令超時服務器設備上的EGD生產和/或消耗量非常大當另一個設備時,可能會導致EGD命令超時錯誤嘗試向該服務器發送EGD命令。如果EGD命令必須搶占正常生產,您可以設置“gcmd_pri”高級用戶參數為2(見GFK-2224,附錄A)。EGD交換生產可能會延遲。
using Ethernet communications
The Ethernet Interface within the CPU module cannot operate on a network until a valid IP address is configured. The necessary Ethernet addressing information must be configured prior to actual network operation, or to recover from inadvertent changes to the Ethernet addressing data at the Ethernet Interface. Use one of the following methods to initially assign an IP address: ? Connect a serial terminal to the Station Manager port of the PACSystems RX7i. Then use the CHSOSW command to enter the desired IP address. For details, see the PACSystems TCP/IP Communications Station Manager manual, GFK-2225. ? Temporarily assign an IP address to the module using the SetIP tool over the Ethernet network. For details, see TCP/IP Ethernet Communications for PACSystems, GFK-2224. ? The Ethernet Interface automatically obtains a temporary IP Address from a BOOTP server on the network. For details, see TCP/IP Ethernet Communications for PACSystems, GFK-2224. Once a temporary IP address has been set up, the Ethernet Interface can be accessed over the network (as by the Machine Edition programming software). The programmer should then be used to configure the proper IP address for the Ethernet Interface. Changing IP address while SRTP connection open may generate log events Open SRTP Server connections established with a remote SRTP client are not terminated as expected when the RX7i’s IP address is changed (typically by storing a new HW Configuration to the RX7i). A Series 90 SRTP client (“SRTP channels”) reports either a 9690H or 0190H status; the SRTP connection may remain open until the connection is terminated as a result of a client timeout.
AUP parameter should not be changed
The Advanced User Parameter “wsnd_buf” should not be changed by the user. Changing the value of this parameter may cause the LAN LED to go out and the Ethernet Interface to drop connection. Heavy load can block Station Manager As explained in TCP/IP Communications for PACSystems Station Manager Manual, GFK-2225, a heavy EGD and/or SRTP load can block Station Manager operation. One-time delay of EGD Production (and possibly Consumption) if more than 24 SRTP Server Connections are started simultaneously If more than 24 SRTP Server connections are established simultaneously, EGD Production may be briefly delayed for each connection after the 24th when the connections are first made after power is applied. If EGD consume acceleration has been disabled, then EGD Consumption will also be delayed. The delay only occurs once when the SRTP Server connection is established for the first time after Powerup. No delay is experienced for the first 24 SRTP Server connections. Very heavy EGD production/consumption at server may cause EGD command timeouts Very heavy EGD production and/or consumption at a server device may cause EGD command timeout errors when another device attempts to send EGD commands to that server. If EGD commands must preempt normal production, you may set the “gcmd_pri” Advanced User Parameter to 2 (see GFK-2224, Appendix A). Note that by doing so, EGD exchange production may be delayed.


公司主營產品圖展示

產品優勢
1:國外專業的供貨渠道,具有價格優勢
2:產品質量保證,讓您售后無憂
3:全國快遞包郵
4:一對一服務
公司主營范圍簡介
PLC可編程控制器模塊,DCS卡件,ESD系統卡件,振動監測系統卡件,汽輪機控制系統模塊,燃氣發電機備件等,優勢品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等



