產品內容介紹
Schumacher 1483-0401A VMDTEOSAVP控制器
內存、時鐘、觸摸面板和功能開關簡介注釋：? 當顯示指示電池電量低的消息時，為面板供電并給電池充滿電。24小時內，電池充電至允許備用操作的水平。完成完全充電需要大約120小時（五天）。? 當電池的環境溫度為40°C（104°F）或更低時，可充電鋰電池的壽命為10年；當電池環境溫度為50°C（122°F）或者更低時，壽命為4.1年；當蓄電池環境溫度為60°C（140°F）和更低時，其壽命為1.5年。用于備份時：? 電池充滿電約100天。? 使用半充電電池約6天*1根據面板的工作溫度和使用年限，時鐘可能會從-380秒/月偏離至+90秒/月。對于這種精度水平不足的系統，用戶應在需要失去通信時進行監控和調整? 通信端口的所有連接不得對端口施加過大壓力。? 將通信電纜牢牢連接到面板或機柜。? 僅使用狀態良好的鎖定系統的D-Sub 9針電纜。不遵守這些說明可能導致人身傷害或設備損壞。電擊當使用SG端子將外部設備連接到面板時：? 設置系統時，請確認沒有創建短路回路。? 對于HMIGTO1300，當主機（PLC）單元未隔離時，將#5 SG終端連接到遠程設備。將#5 SG端子連接至已知可靠的接地連接，以降低損壞電路的風險。? 對于HMIGTO1310，當主機（PLC）單元未隔離時，將#8 SG端子連接到遠程設備。將#8 SG端子連接至已知可靠的接地連接，以降低損壞電路的風險。不遵守這些說明將導致死亡或重傷
串行接口COM2規格
簡介注：有關如何連接控制器和其他類型設備的信息，請參閱屏幕編輯軟件的相應設備驅動程序手冊。串行端口未隔離。SG（信號接地）和FG（機架接地）端子連接在面板內。串行接口COM2 HMIGTO1300:通過RS-485電纜的RJ45連接器注：設置RS-485通信時，某些設備的電纜圖可能需要終端側極化。該終端不需要任何特殊設置，因為它可以自動處理極化。電擊當使用SG端子將外部設備連接到面板時：? 設置系統時，請確認沒有創建短路回路。? 當主機（PLC）單元未隔離時，將#8 SG終端連接到遠程設備。將#8 SG端子連接至已知可靠的接地連接，以降低損壞電路的風險。不遵守這些說明將導致死亡或重傷。所有上述值的設計都考慮了電纜彎曲。此處給出的尺寸是典型值，取決于使用的連接電纜類型。因此，這些值僅供參考。所有上述值的設計都考慮了電纜彎曲。此處給出的尺寸是典型值，取決于使用的連接電纜類型。因此，這些值僅供參考。
Memory, Clock, Touch Panel, and Function Switches
Introduction NOTE: ? When the message indicating that the battery level is low is displayed, supply power to the panel and fully charge the battery. In 24 hours the battery charges to a level that allows backup operation. Completing a full charge requires about 120 hours (five days). ? The lifetime of the rechargeable lithium battery is 10 years when the battery’s ambient temperature is 40 °C (104 °F) or less, 4.1 years when the battery’s ambient temperature is 50 °C (122 °F) or less, and 1.5 years when the battery’s ambient temperature is 60 °C (140 °F) or less. When used for backup: ? Approximately 100 days with a fully charged battery. ? Approximately 6 days with a half-charged battery *1 Depending on the operating temperature and age of panel, the clock can deviate from -380 to +90 sec/month. For systems where this level of precision is insufficient, the user should monitor and make adjustments when required LOSS OF COMMUNICATION ? All connections to the communication ports must not put excessive stress on the ports. ? Securely attach communication cables to the panel or cabinet. ? Use only D-Sub 9-pin cables with a locking system in good condition. Failure to follow these instructions can result in injury or equipment damage.ELECTRIC SHOCK When using the SG terminal to connect an external device to the panel: ? Verify that a short-circuit loop is not created when you set up the system. ? For HMIGTO1300, connect the #5 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #5 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. ? For HMIGTO1310, connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. Failure to follow these instructions will result in death or serious injury
Specifications of Serial Interface COM2
Introduction NOTE: For information on how to connect controllers and other types of equipment, refer to the corresponding device driver manual of your screen editing software. The serial port is not isolated. The SG (signal ground) and FG (frame ground) terminals are connected inside the panel. Serial Interface COM2 HMIGTO1300: RJ45 connector via an RS-485 cable NOTE: When setting up RS-485 communication, the cable diagram for some equipment may require polarization on the terminal side. This terminal does not require any special setting as it handles polarization automatically.ELECTRIC SHOCK When using the SG terminal to connect an external device to the panel: ? Verify that a short-circuit loop is not created when you set up the system. ? Connect the #8 SG terminal to remote equipment when the host (PLC) unit is not isolated. Connect the #8 SG terminal to a known reliable ground connection to reduce the risk of damaging the circuit. Failure to follow these instructions will result in death or serious injury.All the above values are designed with cable bending in mind. The dimensions given here are representative values depending on the type of connection cable in use. Therefore, these values are intended for reference only All the above values are designed with cable bending in mind. The dimensions given here are representative values depending on the type of connection cable in use. Therefore, these values are intended for reference only.
公司主營產品圖展示
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃氣發電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
