產品內容介紹
Harmonic Drive CHM-58A-A-E16384-B-SP控制減速機
(1) 輸出負載線和輸入線應分開并扭曲,以提高噪聲靈敏度。(2) 傳感線應為絞合線或屏蔽線,并與輸出線分開。(3) 使用盡可能粗和短的所有線路,以降低阻抗。電線應扭曲或使用屏蔽線,以提高噪音敏感性。(4) 將電容器連接到負載端子可以消除噪音。(5) 此電源的FG端子為功能接地。為安全起見,將保護接地端子連接到安裝組件接地端子。(6) 端子件的建議扭矩:(7)建議接線建議電路保護器:AC250V30A建議噪聲濾波器:RSEN-2030(TDK-LAMBDA)(8)輸出端子的M4螺釘可能損壞端子的內螺紋。這主要是由M4螺釘?shù)臒o(wú)螺紋部分引起的。因此,請選擇墊圈、彈簧墊圈等,以避免無螺紋螺釘部分穿透輸出端子內部。輸入端子(M4螺釘):1.27 N?m輸出端子(M8螺栓和螺母):10.8N?米
預期壽命電源的壽命取決于使用和安裝風扇的內置鋁電解電容器的壽命??煽啃詳?shù)據中描述了每個壽命。鋁電解電容器的壽命取決于安裝電源的方法、負載電流和環境溫度。請參閱“電解電容器壽命”。風扇的壽命取決于風扇進氣或排氣溫度。請參閱“風扇預期壽命。請不要使用超過預期壽命的產品。存在意外輸出停機的風險,并且可能無法滿足規格要求。請聯系我們進行維護或更換超過預期壽命要求的產品。
外部保險絲額定值
選擇輸入線的外部保險絲時,請參考以下保險絲額定值。當線路接通時,浪涌電流流動。使用慢熔斷保險絲或時間接線片保險絲。不要使用快速熔斷保險絲。保險絲額定值由線路接通時的沖擊電流值規定。在實際負載條件下,不要根據輸入電流(rms.)值選擇保險絲。HWS1500:30A 10.故障排除在確定裝置存在故障之前,進行以下檢查。(1) 檢查額定輸入電壓是否適用。(2) 檢查輸入和輸出接線是否正確。(3) 檢查I/O端子連接是否按規定的擰緊力矩正確擰緊。(4) 檢查導線材料是否不太薄。(5) 檢查輸出電壓控制(V.ADJ)是否正確調整。OVP可能被觸發,輸出被切斷。(6)檢查“+S”和“-S”端子接線是否正確。如果處于打開狀態,輸出的穩定性和準確性會惡化。(7) 如果使用遠程O(píng)N/OFF控制功能,檢查遠程O(píng)N/OFF控制接頭是否未打開。如果處于打開狀態,則輸出被切斷。(8)檢查內置風扇是否未停止。風扇是否因不規則或灰塵等原因而停止。如果風扇停止,PF信號打開。此外,如果風扇停止輸出,保護電路會截獲輸出。風扇是壽命有限的部件。(9) 該電源在前面板和后面板上有通風孔。檢查是否有任何不規則或灰塵等。(10)電源主體是否異常發熱?讓設備充分冷卻后,請?jiān)俅未蜷_(kāi)輸入。輸出被過熱保護功能關閉。(11) 檢查輸出電流和輸出功率是否超過規格。(12) 檢查輸入電壓波形是否為正弦。如果此電源設備連接到UPS,輸入電壓波形可能不是正弦波形。電源設備發出聲音噪音。(13) 在動態負載操作期間,可以聽到可聽的噪音。
Wiring Method
(1) The output load line and input line shall be separated and twisted to improve noise sensitivity. (2) The sensing lines shall be twisted or shield wire and separated from the output lines. (3) Use all lines as thick and short as possible to make lower impedance. Wires are to be twisted or use shield wire to improve noise sensitivity. (4) Attaching a capacitor to the load terminals can eliminate noise. (5) FG terminal of this power supply is functional earthing. For safety purposes, connect protective earthing terminal to the mounting set ground terminal. (6) Recommended torque for the terminal piece: (7) Recommended wiring Recommended circuit protector : AC250V30A Recommended noise filter : RSEN-2030 (TDK-LAMBDA) (8) M4 screw for output terminal might damage the terminal’s inner thread. This is mainly cause by the M4 screw’s unthread section. Therefore, please select a washer, spring washer, etc. to avoid unthread screw section from penetrating into output terminal inner section. Input terminal (M4 screw) : 1.27 N?m Output terminal (M8 Bolt & Nut) : 10.8N?m
The life expectancy The life of the power supply depends on the life of the built-in aluminum electrolytic capacitor being used and mounted fan. Each life is described in reliability data. The life of the aluminum electrolytic capacitor varies depending on the method of mounting the power supply, the load current, and the ambient temperature. Please refer to “Electrolytic Capacitor Lifetime”. The life of the fan depends on the fan intake or exhaust temperature. Please refer to “Fan Life Expectancy. Please do not use the product which passed over the life expectancy. There is a risk of unexpected output shutdown and specifications may not be satisfied. Please contact us for maintenance or exchange the product which passed over the life expectancy.
External Fuse Rating
Refer to the following fuse rating when selecting the external fuses for input line. Surge current flows when line turns on. Use slow-blow fuse or time-lug fuse. Do not use fast-blow fuse. Fuse rating is specified by in-rush current value at line turn-on. Do not select the fuse according to input current (rms.) values under the actual load condition. HWS1500:30A 10. Troubleshooting Before concluding that the unit is at fault, make the following checks. (1) Check if the rated input voltage is apply. (2) Check if the wiring of input and output is correct. (3) Check if the I/O terminal connection is properly tighten by a regulated tightening torque. (4) Check if the wire material is not too thin. (5) Check if the output voltage control (V.ADJ) is properly adjusted. OVP might be triggered and output is cut off. (6) Check if the wiring of “+S” and “-S” terminal is correct. If in open condition, the stability and the accuracy of the output deteriorate. (7) If use function of the remote ON/OFF control, check if the remote ON/OFF control connector is not opened. If in open condition, output is cut off. (8) Check if the built-in fan is not stopped. Is fan stopped by something irregulars or dust, etc. If fan stops, the PF signal is turn on. Moreover, the output is intercepted with the protection circuit if fan stops. Fans are the limited life parts. (9) This power supply has ventilating holes on the front and back panels. Check if there is any irregulars or dust, etc. (10) Is the main body of the power supply abnormally hot? Please turn on the input again after allowing the unit to cool down sufficiently. The output shut down by over temperature protection function. (11) Check if the output current and output power is not applied over specification. (12) Check if the input voltage wave is sinusoidal. If this power supply unit is connected to a UPS, input voltage wave might not be sinusoidal. An audible noise is emitted from the power supply unit. (13) Audible noise can be heard during Dynamic-Load operation.
產品優勢
1:國外專業的供貨渠道,具有價格優勢
2:產品質量保證,讓您售后無憂
3:全國快遞包郵
4:一對一服務
公司主營范圍簡介
PLC可編程控制器模塊,DCS卡件,ESD系統卡件,振動監測系統卡件,汽輪機控制系統模塊,燃?xì)獍l(fā)電機備件等,優勢品牌:Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等




