KONGSBERG SPBUS-HUB輪船控制模塊
第一時間跨度信號校準當按下第一個SPAN按鈕時，所選控制卡的操作與按下SPAN按鈕類似。要進行首次時間跨度校準，請按照第9節步驟（1）至（6）進行，但按下第一個跨度按鈕。注：1.在步驟（6）中，更新量程校準時，新的傳感器校準日期和最后一個傳感器校準日期都將設置為當前日期。2.在為催化傳感器輸入配置的控制卡上，傳感器量程信號值被記錄為新的傳感器值。該值將用于提供傳感器壽命監測數據，方法是將其與隨后使用SPAN按鈕進行校準時獲得的后續值進行比較。注意：此操作需要選擇控制卡，但此操作對所選控制卡沒有影響，該控制卡僅用作顯示設備。要設置時鐘時間和日歷日期，請執行以下操作：（1）將工程鑰匙插入工程卡前面板插座，并檢查解鎖LED（）是否亮起。（2） 按住所需的控制卡RESET/SELECT（重置/選擇）按鈕約1.5秒，并通過顯示選擇圖標檢查所選控制卡是否指示其已被選中。（3） 按下工程卡時鐘按鈕，所選控制卡數字顯示屏將顯示一天中的時間（例如23:59），HOURS值閃爍。（4） 再次按下工程卡時鐘按鈕，所選控制卡數字顯示屏將顯示一天中的時間（例如23:59），MINUTES值閃爍。
傳感器信號監測
SIGNAL（信號）按鈕的操作允許監控所選通道傳感器信號值。顯示的參數取決于安裝在所選通道卡上的傳感器驅動模塊的類型。要進入傳感器信號監測操作，請執行以下操作：（1）按住所需通道卡RESET/SELECT（重置/選擇）按鈕約1.5秒，直到所選圖標出現在通道顯示器上。（2） 按下SIGNAL（信號）按鈕，所選通道卡顯示屏將指示傳感器信號。顯示的值將取決于安裝在通道卡上的傳感器驅動模塊的類型，如下所示：a.催化傳感器驅動模塊顯示屏將顯示在01和02之間測得的帶電電橋電壓（單位：mV）。02是通道卡上惠斯通電橋后半部的中心點。b、 4-20mA傳感器驅動模塊顯示屏將以mA為單位顯示傳感器回路電流。（3）不能更改上述讀數，按下或按鈕將使所選控制卡返回所選模式。根據需要顯示數字值以設置任何新的日期和時間。注：在上述順序中的任何時候按下按鈕都將使工程卡返回所選模式，而不會更改時鐘時間和日歷日期。（9） 按下按鈕，將工程卡實時時鐘設置為新的日期和時間，并將控制卡返回所選模式。
FIRST TIME SPAN SIGNAL CALIBRATION
When the 1st SPAN push-button is pressed, the operation of the selected control card is similar to when the SPAN push-button is pressed. To carry out the first time span calibration, proceed as indicated in Section 9 Steps (1) to (6) but push the 1st SPAN push-button. Note: 1. In Step (6) when the span calibration is updated, the new sensor calibration date and the last sensor calibration date will both be set to the current date. 2. On control cards configured for catalytic sensor inputs, the sensor span signal value is recorded as the new sensor value. This value will be used to provide sensor life monitoring data by comparison with subsequent values obtained during later calibrations using the SPAN button.Note: This operation requires a control card to be selected but the operation has no effect on the selected control card, which is used as a display device only. To set the clock time and calendar date, proceed as follows: (1) Plug the Engineering Key into the Engineering Card front panel socket and check that the Unlocked LED ( ) is illuminated. (2) Push and hold the required control card RESET/SELECT pushbutton for approximately 1.5 seconds and check that the selected control card indicates it has been selected by displaying the select icon. (3) Push the Engineering Card CLOCK push-button and the selected control card digital display will show the time of day (eg. 23:59) with the HOURS value flashing. (4) Push the Engineering Card CLOCK push-button a second time and the selected control card digital display will display the time of day (eg. 23:59) with the MINUTES value flashing.
SENSOR SIGNAL MONITORING
The operation of the SIGNAL push-button allows the monitoring of the selected channels sensor signal value. The displayed parameter is dependent upon the type of sensor drive module fitted to the selected channel card. To enter the sensor signal monitoring operation, proceed as follows: (1) Push and hold the required channel card RESET/SELECT pushbutton for approximately 1.5 seconds until the selected icon appears on the channel display. (2) Push the SIGNAL push-button and the selected channel card display will indicate the sensor signal. The displayed value will depend on the type of sensor drive module fitted to the channel card as follows: a. Catalytic Sensor Drive Module The display will show the live bridge voltage measured between 01 and 02 in mV. 02 is the centre point of the second half of the Wheatstone bridge which is on the channel card. b. 4 - 20mA Sensor Drive Module The display will show the live sensor loop current in mA. (3) No alterations can be made to the above readings and pressing either the or push-buttons will return the selected control card to the selected mode.displayed numerical value as required to set any new date and time. Note: Pressing the push-button at any time during the above sequence will return the Engineering Card to the selected mode without changing the clock time and calendar date. (9) Press the push-button to set the Engineering Card real time clock to the new date and time, and return the control card to the selected mode.
產品優勢
1：國外專業的供貨渠道，具有價格優勢
2：產品質量保證，讓您售后無憂
3：全國快遞包郵
4：一對一服務
公司主營范圍簡介
PLC可編程控制器模塊，DCS卡件，ESD系統卡件，振動監測系統卡件，汽輪機控制系統模塊，燃?xì)獍l(fā)電機備件等，優勢品牌：Allen Bradley、BentlyNevada、ABB、Emerson Ovation、Honeywell DCS、Rockwell ICS Triplex、FOXBORO、Schneider PLC、GE Fanuc、Motorola、HIMA、TRICONEX、Prosoft等各種進口工業零部件、歐美進口模塊。
產品廣泛應用于冶金、石油天然氣、玻璃制造業、鋁業、石油化工、煤礦、造紙印刷、紡織印染、機械、電子制造、汽車制造、塑膠機械、電力、水利、水處理/環保、鍋爐供暖、能源、輸配電等等
