ICS TRIPLEX 9451處理器模塊
6.要驗證消息是否已添加，請查看S1 469 SETUP（設置）×DEFAULT MESSAGES（默認消息）子組中的最后一條消息。使用以下步驟刪除默認消息：1。為S1 469 SETUP（設置）passcode（密碼）Enter passcode for ACCESS（進入密碼）設定點輸入正確的密碼（除非密碼已輸入或密碼為“0”，否則會破壞密碼安全功能）。2.在S1 469 SETUP（設置）×DEFAULT MESSAGES（默認消息）子組下選擇要?jiǎng)h除的消息。3.當顯示要?jiǎng)h除的默認信息時，按。繼電器顯示PRESS[ENTER]TO REMOVE DEFAULT MESSAGE（按下[ENTER]TO刪除默認信息）消息。4.按下可從默認消息列表中刪除當前消息。5.如果正確遵循該程序，將顯示以下閃光消息：n默認消息n[ENTER]了解更多電機狀態：停止范圍：n/A A:0 B:0范圍：n/A電機負載：0.00 x FLA范圍：n/B當前不平衡：0%范圍：n/C日期：1995年1月1日時間：12:00:00范圍：不適用MULTILIN 469電機管理繼電器范圍MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESTAGE MESSAGE MESSAGE ENTER ENTER ENTER輸入4-10 469電機管理繼電器GE Multilin 4.2 S1 469 SETUP 4 SETPOINT 4 4.2.6 MESSAGE SCRATCHPAD PATH:SETPOINT？S1 469設置？MESSAGE SCRATCHPAD最多可在消息草稿區域下編程五（5）個消息屏幕。這些信息可能是與安裝或電機相關的注釋?zhuān)蛴脩?hù)認為相關的任何其他信息。此外，可以在默認消息顯示期間選擇這些消息進行掃描。這可能有助于提醒操作員執行某些任務?？梢詮耐ㄐ哦丝诨蛲ㄟ^(guò)鍵盤輸入消息。以下過程演示了消息草稿行的使用：1。選擇要更改的用戶消息。2.按十進制[.]鍵進入文本模式。下劃線光標將出現在第一個字符下。3.使用/鍵顯示所需字符?？崭衽c字符一樣被選中。4.按十進制[.]鍵前進到下一個字符。要跳過字符，請按十進制鍵。如果意外存儲了不正確的字符，請按十進制鍵足夠多次以將光標滾動到該字符。5.當顯示所需信息時，按存儲或退出。該消息現在永久存儲。按下可取消更改的消息。4.2.7清除數據路徑：設置點S1 469設置×清除數據n消息SCRATCHPAD n[ENTER]（輸入）更多文本1范圍：40個字母數字字符文本2范圍：40字母數字字符TEXT3范圍：40字符數字字符文本4范圍：40位字母數字字符MULTILIN 469電機管理繼電器范圍：40字節數字字符n清除數據n[ENTEP]（輸入]更多清除上次跳閘數據：否范圍：否，是重置MWh和Mvarh儀表：否范圍：否、是清除峰值需求數據：否范圍，是清除RTD最大值：否范圍；否，是清除模擬I/P最小值/最大值：無范圍：否；是清除跳閘計數器：否范圍，是的，輸入ESCAPE（退出）信息
6. To verify that the message was added, view the last message in the S1 469 SETUP ?× DEFAULT MESSAGES subgroup. Use the following procedure to remove default messages: 1. Enter the correct passcode for the S1 469 SETUP ? PASSCODE ? ENTER PASSCODE FOR ACCESS setpoint (unless the passcode has already been entered or unless the passcode is “0”, defeating the passcode security feature). 2. Select the message to remove under the S1 469 SETUP ?× DEFAULT MESSAGES subgroup. 3. When the default message to be removed is shown, press . The relay displays the PRESS [ENTER] TO REMOVE DEFAULT MESSAGE message. 4. Press to remove the current message from the default message list. 5. If the procedure was followed correctly, the following flash message will be displayed: n DEFAULT MESSAGES n [ENTER] for more MOTOR STATUS: Stopped Range: N/A A: 0 B: 0 Range: N/A MOTOR LOAD: 0.00 x FLA Range: N/A CURRENT UNBALANCE: 0% Range: N/A DATE: 01/01/1995 TIME: 12:00:00 Range: N/A MULTILIN 469 Motor Management Relay Range: N/A DEFAULT MESSAGE HAS BEEN ADDED DEFAULT MESSAGE HAS BEEN REMOVED ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE MESSAGE ENTER ENTER ENTER ENTER 4-10 469 Motor Management Relay GE Multilin 4.2 S1 469 SETUP 4 SETPOINTS 4 4.2.6 MESSAGE SCRATCHPAD PATH: SETPOINTS ? S1 469 SETUP ?× MESSAGE SCRACTHPAD Up to five (5) message screens can be programmed under the Message Scratchpad area. These messages may be notes that pertain to the installation or the motor or any other information deemed pertinent by the user. In addition, these messages may be selected for scanning during default message display. This might be useful for reminding operators to perform certain tasks. The messages may be entered from the communications ports or through the keypad. The following procedure demonstrates the use of the message scratchpad: 1. Select the user message to be changed. 2. Press the decimal [.] key to enter text mode. An underline cursor will appear under the first character. 3. Use the / keys to display the desired character. A space is selected like a character. 4. Press the decimal [.] key to advance to the next character. To skip over a character press the decimal key. If an incorrect character is accidentally stored, press the decimal key enough times to scroll the cursor around to the character. 5. When the desired message is displayed press to store or to quit. The message is now permanently stored. Press to cancel the altered message. 4.2.7 CLEAR DATA PATH: SETPOINTS ? S1 469 SETUP ?× CLEAR DATA n MESSAGE SCRATCHPAD n [ENTER] for more TEXT 1 Range: 40 alphanumeric characters TEXT 2 Range: 40 alphanumeric characters TEXT 3 Range: 40 alphanumeric characters TEXT 4 Range: 40 alphanumeric characters MULTILIN 469 MOTOR MANAGEMENT RELAY Range: 40 alphanumeric characters n CLEAR DATA n [ENTER] for more CLEAR LAST TRIP DATA: No Range: No, Yes RESET MWh and Mvarh METERS: No Range: No, Yes CLEAR PEAK DEMAND DATA: No Range: No, Yes CLEAR RTD MAXIMUMS: No Range: No, Yes CLEAR ANALOG I/P MIN/MAX: No Range: No, Yes CLEAR TRIP COUNTERS: No Range: No, Yes PRESET DIGITAL COUNTER: No Range: No, Yes CLEAR EVENT RECORDER: No Range: No, Yes ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE VALUE VALUE ENTER ESCAPE ESCAPE ENTER ESCAPE e e MESSAGE ESCAPE MESSAGE ESCAPE MESSAGE ESCAPE
